Tags

, , , , , , , ,

A few months ago, I built a Harvest Table for my wife to use in her booth to sell some of her antiques. You can read the blog post here. She still has that table, but she asked me to build another one for another booth she has. I went to a local antique store that sells reclaimed wood and bought a 4″ square posts and three pieces of barn wood siding. I have a picture of the wood on instagram. Unfortunately, I deleted the original photo from my phone before I uploaded it to photobucket to share here.

I started this harvest table in much the same way as the first one, turning the legs on the lathe. The major difference is that this table was turned with reclaimed birch instead of douglas fir 4×4’s that I bought at Lowe’s. Turning reclaimed lumber is probably not the smartest thing to do since you never know what the integrity of the wood is as it may snap off while on the lathe injuring you, but I thought I’d take my chances.

A couple of the pieces I wanted to turn had some nails stick stuck in the wood. I grabbed a chisel and hammer and I dug into the wood to extract all nails I could find. There were a couple of nails that were too deep to grab, so I carefully turned the leg, stopping every few strokes making sure I wasn’t near the top of the nail.

 photo 20160905_195121.jpg

While a couple of the posts had nails holes in them, the other two had old worm holes. I turned each leg the same and in the end, they were full of character. You can see the final four turned legs here.

 photo 20160905_195135.jpg

With the legs turned, I focused my attention on the top. I took the three slabs of barn wood siding and brought them together to determine how wide the top of the table could be. The boards were only 3/4″ thick and I wanted the top to be thicker, so I took some scrap OSB boards I had laying around from when I was building my shed and built a substrate for the boards.

 photo 20160904_183146.jpg

I glued and screwed the OSB to the siding gluing in the middle of the boards and screwing on the ends. The siding is so old that I figure the expansion and contraction of the wood would be very minimal. Even if they did crack, it would just add more character to the top of the table.

 photo 20160905_161649.jpg

I added some pine edging to cover up the OSB substrate underneath the top boards. Cutting the corners is where my miter trimmer comes in handy. I love that thing!

 photo 20160905_160457.jpg

Flipping the top back over, I figured out where the legs should go. I kept the design simple by using a scrap pieces of edging that were 1 3/8″ wide and making them gauges to show me where the legs should go. Easy P-easy.

 photo 20160905_162059.jpg

Next was to make the frame of table. I grabbed a 2×12 and milled it to 3/4″ thick by 5″ wide pieces and cut them to fit between the legs.

 photo 20160905_163615.jpg

I then channeled my inner Scott Phillips of The American Woodshop and used my Kreg Pocket Hole Jig and screwed the frame to the top. I was trying to build this table as quick and as easy as possible. I wasn’t trying to win a woodworking contest with this table.

 photo 20160905_170752.jpg

I still needed to attach the legs to the frame so I drilled a pilot hole in the legs and screwed in 3/8″ hanger bolts.

 photo 20160905_175850.jpg

I then simply drilled a hole in the corner brackets, fed the bolt through the hole, and tightened it in place with a nut. As the nut tightened to the corner bracket, it drove the leg tight to both sides of the frame. Attaching the legs this way makes it possible to take them off and carry it out of my basement shop.

 photo 20160905_181837.jpg

Flipping it back over, the table was built. Super simple and super fun. I posted this picture on instagram and it has been my most liked picture, ever!

 photo 20160905_195802.jpg

The final picture is the table with an antique stain applied to it. I’m happy with the way it turned out and so is my wife.

 photo 20160906_183410.jpg

Advertisements