Repairing the Foot of a Walnut Table

A few weeks ago, my wife and I, were visiting thrift shops in Cincinnati when we ran across a round walnut table for $20.00 at Goodwill. There was nothing special about it. It had a dull flat finish and was missing the extension wings that go in the middle. It even had two feet that were broken. Anita asked me if I could remake them and I told her I could, so we took it home.

20180121_113259.jpg

In order to fix the feet, I grabbed some scrap walnut and glued pieces to them to re-sculpt the feet.

20180121_133246.jpg

Once the glue dried, I cut the arch of the foot with my band saw, then I sawed off the sides with a hand saw.

IMG_20180127_142412_194.jpgIMG_20180127_142412_192-1.jpg20180127_122245.jpg

Next, I stuck the leg on the lathe and turned the pad of the foot.

IMG_20180127_142412_201.jpg

I then brought the foot over to my workbench and carved the rest of the foot by hand using chisels and rasps.

IMG_20180127_142412_203.jpg

After shaping the foot was complete, I started to sand the leg with 80 grit sand paper working down to 220 grit.

IMG_20180127_142412_206-1.jpg

With the foot finished, I was happy with the way it turned out as it matched the other two. I then repeated the same steps for the other broken foot.

IMG_20180127_142412_208-2.jpg

Noticing the top was solid walnut, I decided to sand off the dull stained finish. You can see how bland the table was when we bought it.

20180128_111309.jpg

A few minutes of sanding, the table was really starting to shine again.

20180128_121515.jpg

After applying three coats of hemp oil, you can see how the table has been brought back to life having much more character between the sap and heart wood of the walnut. Looks much nicer than the boring spray toner stain that was on it before. This piece will be a nice addition in my wife’s booth as a display table.

IMG_20180130_172822_954.jpg

Advertisements

Whiskey Barrel Coffee Table

My cousin had been asking me to make a whiskey barrel coffee table for her for over a year. I put it off for months because I didn’t know where to buy a whiskey or wine barrel until I ran across a guy on Craigslist who sells them out of his house. Even better, he sells half barrels which was perfect for me as I really didn’t feel like cutting a barrel in half.

20170820_202148.jpg

When I got the barrel home, I let it acclimate in my shop for a few weeks. As the barrel dried out, the staves started to fall apart, so I clamped them together using band clamps until I was able to screw fasteners into each stave to hold it in place. While the band clamps were holding the whole barrel together, I laid it on top of white oak boards I bought at a sawmill to see how big I wanted to make the top of the coffee table.

20170927_091615.jpg

To keep the barrel together, I screwed hex bolts through the bands into the wood to hold each stave in place. I also leveled the top of the barrel by sanding the edges straight with my belt sander. The barrel came with a stand for it to be used as an outside planter which was helpful in holding it in place while I worked on it.

img_20171023_081036_611.jpg

My wife didn’t like the look of the hex bolts I used so, I replaced them with #14 stainless steel pan head screws. She was right, the pan head screws look much nicer.

20171104_112336.jpg

I designed the shape of the legs by using the stand that came with the barrel to shape the curves. Each leg had an angle to the top that fit the angle of the barrel as it laid flat. I chamfered the edges of the feet to mimic the chamfers on the top and bottom of the barrel.

IMG_20171105_174750_413.jpg

You can see how I used the compass to figure out the gap that I needed to shave off the other side of the leg in order for the barrel to fit tight.

20171105_130250.jpg

Once I was happy with the legs, I focused on the frame of the barrel. I traced the shape of the barrel onto a piece of wood and cut it out on my band saw. I then trimmed the end of the sides 90 degrees to the edge and double-stick taped it to the other side. This allowed me to clamp the whole frame while it was screwed and glued together.

20171105_120020.jpg

After carefully measuring all the pieces, I test fitted the frame together to make sure it would fit nicely on top of the barrel.

IMG_20171105_145213_229.jpg

I was more aggressive with the clamps when it came time for the actual glue up. I let this set in place for 24 hours.

20171105_184017.jpg

As the base was setting up, I turned my attention to the top. I glued up several white oak boards together and flattened them with my hand planes because the panel was too wide to fit through planer.

20171028_135625.jpg

I wanted the top to have a bread board edge so I plowed a groove into the ends that was the same width as my 3/8″ mortising chisel. I would later chop three mortises into the groove to fit tenons I would make.

20171028_152808.jpg

To make the tenons, I used both power and hand tools to get the job done. I routed most of the material away with my plunge router, then finalized the fit with my Stanley No 10 1/2 rabbet plane.

20171028_150436.jpg

I made sure the panel would fit into to the groove before I cut the tenons

20171028_152719.jpg

Cutting out the tenons, I drilled holes through the middle for pins. The middle hole I left round while the tenons on the outside I elongated for the expansion and contraction of the wood.

20171029_124858.jpg

Once the joints fit well, I drove pins into the holes and added a dab of glue so the pins wouldn’t fall out.

20171029_131304.jpg

I shaped the sides of the top to match the curve of the barrel and lightly rounded over the sides with my hollow molding plane.

20171111_122834.jpg

The final shape of the coffee table top came out nicely. Now I needed to find away to attach it to the frame.

20171111_124241-1.jpg

After days of pondering, I decided to attach hinges to the top so that the lid could open and close. The inside of the barrel was charred from the brewing of the whiskey so, it’s not very useful as it will leave ash on your finger if you touch it, but I thought it was cool enough to show off. I clamped my level to the middle of the frame to determine where in proximity the hinges would need to be installed.

20171111_130736.jpg

Because the lid overhangs the side by an inch, the barrel of the hinges lay underneath the top when closed. I had to rout out a recess on the underneath of the lid so the top could properly close.

20171111_142117.jpg

Even with all my calculating, I ran into a problem. The top would hit the middle of the barrel when I tried opening it. I had to route a recess in the middle of the lid so that there would be enough room for the lid to open. It took several hours of trial and error to make it work, but I finally made it work.

20171111_153501-1.jpg

Once everything worked, I sanded the entire coffee table to 220 grit sand paper and applied a weathered wood enhancer to blend the old barrel to the new white oak. This turned the coffee table a bit purplish gray.

20180113_130306.jpg

Next, I stained it Minwax Espresso stain and applied three coats of water based polyurethane for a protective finish. I think the coffee table turned out really nice. Luckily, my work has me going to Detroit next week, so I can deliver the coffee table to my cousin.

IMG_20180203_075400_114.jpg

 

Making Floating Shelves

My wife, Anita wanted me to make some custom floating shelves for the dining room. We had some floating shelves from Ikea, but she wanted something that would match the coffee bar I made her.

Making the shelves were super easy. I grabbed 3/4″ pine and a couple of 2 x 2 select pine from Home Depot. I made the width of the shelves 3 1/8″ thick so that the 2 x 2 would fit inside nicely without getting jammed inside.

20170813_135623

I used my miter jack to make sure the sides were a perfect 45 degrees so all the pieces would fit nicely together with no gaps. Most people make these shelves with simple butt joints on the ends, but I didn’t want end grain showing so I took the time to miter the corners.

20170813_135638

After making sure everything fit together well, I glued and clamped the whole assembly together.  Anita then stained the shelves with apple cider vinegar, steel wool solution and gel stain to match the coffee bar.

20170813_144147

When it came to install the shelves, I attached the 2 x 2 frame to the wall by securing it to the studs making sure it was level.

20170822_203058\

I then slid the shelf into place and secured it in place from the bottom into the 2 x 2 frame.  I then did the exact same thing on the second shelf.

20170822_203808

Here are the shelves installed with a bunch of Rae Dunn pottery on them. Anita was planning on writing messages on the chalk board wall to give it some pizzazz, but decided the wall is too dark and will eventually paint it back normal. What do you think? Should she give the chalk board wall a shot with fancy chalk board writing on it?

20171010_095354.jpg

She painted the wall.

20171017_170847.jpg

Big Ole Wood Shelf

Several months ago, I started making a shelving unit out of southern yellow pine that my wife asked me to make for her booth. I got this far and it sat in my shop unfinished for months. After much contemplation, my wife and I both realized that the shelving unit was really too big to fit in our Ford Edge.

20170722_120716.jpg

The best thing we could do, is take it apart and resize the thing smaller so we wouldn’t have to rent a trailer to transport it. Luckily, I put the shelf together almost entirely with pocket screws. The part that was glued, I cut apart on the band saw.

20170722_122654

After, I cut the shelves shorter, I used my router and cut floating tenons on all the pieces instead of using pocket holes screws like I did before.

20170722_131434

A few hours later, I had the new resized shelving unit put back together. The height stayed the same at five feet, but the length was cut down from five feet to forty inches so that it would fit in our car.

20170722_171943

My wife always wanted the unit to roll so I added four old casters to the bottom. We actually bought the casters many months before we decided to make the shelving unit just in case someday we needed them.

20170723_100917

With 1/2″ plywood installed for the shelves, the unit was built, but unfinished.

20170723_102601

Anita wanted the unit to look somewhat old, so I smacked the wood around with a hammer and crowbar to give it an aged look.

20170723_123747

I bought a few piece of thin gauge metal, drilled some holes in it, bent it over in my vise, painted them black, and screwed them to the corners of the shelving unit to give it a more industrial look. The brackets and the dark stain really makes the unit pop. Now it was ready to throw in the Edge and bring it to our booth. Saved us $50 not having to rent a trailer and we both feel it looks nicer then it did before.

IMG_20170812_133702_428

 

Everyday Console Table

I call this piece the “everyday table” because you see this design everyday. I spotted this one at Home Goods just last week. It’s kind of a cross between a table and a bookcase. As far as construction goes, it’s very simple. Six framed legs with a top, a couple of shelves and a cross “X” on each side. In fact, there’s a website that shows how to build this table, pocket screws and all.

20170709_141125

Say what you want about the design and construction, but they are very popular and super easy to build. My wife found the website the other week and asked me to customize one to fit in our dining room as a coffee bar.

20170604_153948

Being true to form, I built ours out of southern yellow pine (2 x 10’s). I wasn’t a fan of the thick 2 x 4 legs so I milled all the parts down to 1″ thick.

img_20170605_111353_327

Keeping it simple, I used pocket screws and glue to attach all the pieces. The shelves are southern yellow pine boards I ripped and glued back together to create a quarter sawn panel so they wouldn’t expand and contract too much.

20170604_140643

The hardest part about building the piece are the X’s on the sides, but all that entails is cutting a couple of half lap joints.

20170604_141457

Here is the finished bar with a vinegar steel wool solution and gel stain on top to give the wood some depth. The coffee bar has turned more into a display table for my wife’s Rae Dunn collection, but that is another story for another day.

20170717_205426

I have since played around with the design again and built another one using eastern white pine. Construction is similar except I used floating tenons instead of pocket screws to build the frames. I’ll still use the vinegar and steel wool solution again on this one and stain it a dark color. My third design will probably have a thicker top and I may use plywood for the shelves. Stay tuned.

20170716_173034

 

 

Building a Shed Part XII

While browsing through the Weaver Barn catalogue, Anita saw this cool looking arbor over a couple of doors. We decided that an arbor like this would look really nice over our side window.

 photo 20161022_120709.jpg

To begin construction on the arbor, I grabbed some scrap cedar I had from building the shed and made about 24 slats. The slats were about 1  3/4″ wide by 13″ long with a little 1″ arch at one end.

 photo 20161022_115046.jpg

Designing simply from a picture can be tough, so I grabbed a scrap piece of 6″ wide cedar, cut out a 4″ diameter arch and placed it around my corbel to see how to design the overall arbor.

 photo 20161022_121136.jpg

The distance between the corbels is 6′ with the overall length of the arbor being 87″. I originally planned 25 slats about 3 1/2″ apart, but Anita thought it was a little too many slats.

 photo 20161022_144036.jpg

We ended up deciding to use 21 slats 4″ apart. I wanted the slats to fit in place so I cut some dadoes in the wood to house the slats. Using  my dovetail saw, router plane, and rasps, I easily cut the dadoes in no time.

 photo 20161023_131336.jpg

I cut a small dado on each of the slats as well and test fitted the arbor together.

 photo IMG_20161023_130104.jpg

Since the slats had a dado, I decided the corbels should have dadoes as well to keep everything in line.

 photo 20161023_111052.jpg

I also wanted the arbor to fit inside the corbels so I cut notches in both the front and back where the corbels would go.

 photo 20161023_115614.jpg

I fit everything back together and drilled the slats to fit on the front and back. I used stainless steel screws so that they wouldn’t stain the arbor like galvanized screws would.

 photo 20161023_133945.jpg

Dry fitting everything together the arbor started to come together nicely, so it was time to stain it.

 photo 20161023_134513.jpg

I stained the arbor the same Benjamin Moore Cedar Bark stain we used on the shed.

 photo 20161023_145637.jpg

However, after living with the color of the stain on the shed for a few weeks, we weren’t too happy with the color. So, after the first coat of Cedar Bark from Sherwin Williams, Anita mixed in a pint of Leather Saddle Brown with a touch of Fresh Brew stain from Benjamin Moore. Since all three stains were water based, they mixed together well.

 photo 20161027_152844.jpg

After I applied the new coat, the cedar took on a much warmer color. We were very pleased.

 photo 20161027_152903.jpg

Anita helped me install the arbor so I don’t have any pictures of it being installed as I wasn’t in the mood to tell her to hold onto the arbor while I stop and take some pictures. I started out measuring the length of the window frame and calculated how much on each end the corbels would need to be in order for the arbor to be in the middle of the window. The window frame was 67″ while the distance between the corbels was 72″. That left me with 2 1/2″ on each side of the window. I marked the spot and then decided how far above the window I wanted the arbor to be. Once I got that measurement, which was 2 1/2″ as well, I nailed the left corbel in place with 2 1/2″ galvanized pneumatic nails. Then, I placed the arbor on top of the corbel, leveled it, and then shot nails in the arbor itself, attaching it through the siding into the studs of the shed. I then screwed my stainless steel screws through my pocket holes attaching the arbor to the corbel to tighten everything up. Next, I took the right corbel and stuck it up into the recess of the arbor, nailed and screwed it up just as I did to the left one. Finally, I screwed and nailed the back side of the arbor to the shed.

 photo IMG_20161030_155615.jpg

As you can see, I think we made a good decision darkening the cedar stain. The cedar looks richer and blends better with the gray paint.

 photo IMG_20161031_100223.jpg

Revamping a Dining Table

About twelve years ago I built a dining table from the plans out of Woodsmith magazine. While it served it’s purpose, it wasn’t exactly the nicest thing in the house. I made the top out of a piece of low-grade oak plywood that I bought at Home Depot. Not only that, but the table was huge being 44″ wide. My wife Anita asked if I could make a new one, or at least make a new top that was more in style. We decided that making a new top out of southern yellow pine and try weathering it making it look aged.

 photo 20150713_192149.jpg

The easy part was buying four 2 x 10’s, ripping them 9″ wide by six feet long and gluing them together. After they were glued, I planed the tops of the boards straight removing all the mill marks in the process.

 photo 20150713_181813.jpg

After the top was planed and sanded with 150 grit sandpaper, Anita applied mixture of steel wool and apple cider vinegar onto the boards to tone down the yellowness of the southern yellow pine.

 photo blog 002_4.jpg

We thought it would be a good idea to stain the top while it was already on the table. I removed the original top of the table and flipped over the base onto the new top to decide how much I would need to cut the sides down.

 photo blog 004_6.jpg

After messing around with the legs for a few minutes, I decide that the sides should be 24″ wide.

 photo blog 005_6.jpg

I cut the sides to 24″ and rerouted the dado on both boards for the corner brackets. I then used pocket screws to re-attach the sides to the legs.

 photo blog 006_2.jpg

Using metal corner brackets, I simply attached the top to the base. The new top made the table look more like a farm table.

 photo blog 008_1.jpg

Anita then stained the table with Special Walnut, then Classic Gray stain from Minwax.

 photo 1437251379798.jpg

Once dry, she applied hemp oil and gave the top a good waxing. She then painted the base with grey chalk paint. When done, it looked like a completely different table.

 photo 20150724_171103.jpg

A close up the table you can see how the southern yellow pine took on a deep rich tone. You can also see how the original black paint shows through the grey paint after Anita sanded the base a little bit. This has been one of those projects we should have done years ago.

 photo 20150724_171113.jpg